Results 1 to 9 of 9

Thread: exhaust bottoming out (damnit)

  1. #1
    Inactive Member Ladynredsi's Avatar
    Join Date
    March 4th, 2001
    Posts
    735
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Angry

    jer put on the rear Wings West bumper for me last night. as most of you know i only have maybe an inch & half (2" at most) ground clearance with that exhaust. he had to lower the exhaust some so the tailpipe would fit the cut out in the bumper. now the exhaust isn't even 1/2" off the ground eek

    i know when i stick my enkei's back on it'll bring the car a little more off the ground. but not enough. does anyone know how i would go about bending or getting the piping bent from the canaster to the tip. if it were bent downwards then the tip would clear the bumper cut out and the canaster can be raised back up where it was.

    damn...did any of that make sence? LOL!

    ami

    ------------------
    www.4thgenerationcivic.com

    "Hi, my name is Ami and I'm a Honda-coholic"

    My Si:
    http://www.members.tripod.com/4thgencivic/id41.htm

  2. #2
    Inactive Member 4g88civicS's Avatar
    Join Date
    October 15th, 2001
    Posts
    84
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    Try to find someone that does custom exhausts. I have had pipes bent before by ehxuast people, they have a machine that bends it. If you know anyone who could do that, let them take a look at it and see if they could bend it around for you!

    aDAM

    ------------------
    "I need 2 of the big bottles...by tonight!"
    ~Brain Spillner~
    hahaha

  3. #3
    Inactive Member Jmunk's Avatar
    Join Date
    November 21st, 2001
    Posts
    99
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    I do custom exhaust, and for our cars the best thing to do in your case would be to would be to take it to a shop that does cutsom exhasut and tell them your problem and tell them how you want the muffler to hang. It's a difficult situation but if they are good than they should be inventive and be able to figure out something. If not than let me know and i will see what i can figure out.

    ------------------

  4. #4
    HB Forum Owner CWBETB's Avatar
    Join Date
    March 1st, 2001
    Posts
    1,609
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    Ami I actually have the same problem and this week Im going to a muffler shop to get my canon choped off and to get a small dual tip so the exhuast doesnt hang low smile

    P.S. Ami link this link for the message board for now http://members.shaw.ca/c90civicrider...rame-index.htm


    ------------------
    90 Civic Turbo ZC

    Home Page:
    http://www.geocities.com/cwbetb

    4th Gen Page:
    http://www.geocities.com/hondacivic4g

    Car Club:
    http://www.teamkayo.com

  5. #5
    Inactive Member RedRacerCivic's Avatar
    Join Date
    April 19th, 2001
    Posts
    231
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    what i would do is cut off the piping and have it mandrel bent upward so that your muffer remains horizontal. smile

    ------------------
    My little '91 Si
    http://hometown.aol.com/skatemesa1
    Kill list:
    95' geo metro
    00' goped
    69' pinto
    92' suzuki swift
    97'garbage truck
    old lady in a buick
    school bus

  6. #6
    Inactive Member civickiller's Avatar
    Join Date
    August 31st, 2001
    Posts
    57
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    I would say just trim the bumper little bit, i mean it only an inch or so

    ------------------

  7. #7
    Inactive Member Ladynredsi's Avatar
    Join Date
    March 4th, 2001
    Posts
    735
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Angry

    well, my exhaust has to go frown this is a sad day. i liked it. jer took it to our "muffler" guy. yada,yada,yada...it's not worth it. i'll just sell it frown

    who has an exhaust that fits well with their WW rear bumper? what brand is it?

    thanks.

    ami

    ------------------
    www.4thgenerationcivic.com

    "Hi, my name is Ami and I'm a Honda-coholic"

    My Si:
    http://www.members.tripod.com/4thgencivic/id41.htm

  8. #8
    Inactive Member marked001's Avatar
    Join Date
    March 4th, 2001
    Posts
    795
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    ...if you dont wanna get a new exhaust, just trim the bumper and the mesh like previously mentioned..doesnt look bad...

    ------------------
    www.marked001.com
    under construction

    [email protected]

    illadelphia, PA

  9. #9
    Inactive Member habib_88's Avatar
    Join Date
    March 19th, 2001
    Posts
    328
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Lightbulb

    I bought smaller rubber hangers for my muffin shooter, that brought it up like a 1/2 inch to inch higher with no other problems. But with the WW kit i dunno how that helps ya. I would keep it...you have enought civics its gonna have to fit on one of them hehe. If not, cut it up...mount the muffer itself on your VW...i'm always thinking Ami wink biggrin

    ------------------
    Suspenion Mods- More than you can shake a stick at...
    Brake mods- I could slow down a buick if needed
    Engine mods- Shit I knew I forgot something

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •